


Low-voltage series
XL Series Power Distribution Cabinet
The XL series low-voltage power distribution cabinet is suitable for power and lighting distribution in three-phase four-wire power systems with an AC frequency of 50 Hz and a voltage of 400 V and below in industrial and civil buildings. It is also suitable for making various motor starting cabinets, including full-voltage direct-on-line starting cabinets, all-digital control soft starter cabinets, autotransformer reduced-voltage starting cabinets, star-delta starting cabinets, multi-speed motor starting cabinets, etc. Dozens of primary circuit scheme numbers or derived scheme numbers are available for selection, giving a wide range of applications. This product is an indoor enclosed distribution box. The enclosure is bent and welded from thin steel plate; the front has a single left-opening door fitted with measuring instruments such as a voltmeter and ammeter, and with operating and signal devices. It is a power distribution device with a simple structure, reliable operation and relatively low cost. The XL series products comply with the following standards: IEC 61439 Low-voltage switchgear and controlgear assemblies; GB/T 7251.12 Low-voltage switchgear and controlgear assemblies Part 2: Assemblies for power distribution and control.
Request a quotePlease provide your operating conditions, quantity and required connection or output.
Technical details
Specifications from source material
The XL series low-voltage power distribution cabinet is suitable for power and lighting distribution in three-phase four-wire power systems with an AC frequency of 50 Hz and a voltage of 400 V and below in industrial and civil buildings. It is also suitable for making various motor starting cabinets, including full-voltage direct-on-line starting cabinets, all-digital control soft starter cabinets, autotransformer reduced-voltage starting cabinets, star-delta starting cabinets, multi-speed motor starting cabinets, etc. Dozens of primary circuit scheme numbers or derived scheme numbers are available for selection, giving a wide range of applications. This product is an indoor enclosed distribution box. The enclosure is bent and welded from thin steel plate; the front has a single left-opening door fitted with measuring instruments such as a voltmeter and ammeter, and with operating and signal devices. It is a power distribution device with a simple structure, reliable operation and relatively low cost. The XL series products comply with the following standards: IEC 61439 Low-voltage switchgear and controlgear assemblies; GB/T 7251.12 Low-voltage switchgear and controlgear assemblies Part 2: Assemblies for power distribution and control.
- Note
- If users have special requirements, these can be resolved through consultation with the manufacturer
- Rated operational voltage (Ue)
- V 380
- Rated operational current (In)
- A ≤600
- Rated frequency (Fn)
- Hz 50
- Rated insulation voltage (Ui)
- V 660
- Rated short-time withstand current (Icw)
- kA 10
- Rated peak withstand current (Icw)
- kA 17
- Rated impulse withstand voltage (Uimp)
- kV 6
- Overvoltage category
- IV
- Pollution degree
- 3
- Clearance
- ≥10 mm
- Creepage distance
- ≥12.5 mm
- Degree of protection
- IP30 (customizable on special request)
Full product details
Overview
The XL series low-voltage power distribution cabinet is suitable for power and lighting distribution in three-phase four-wire power systems with an AC frequency of 50 Hz and a voltage of 400 V and below in industrial and civil buildings. It is also suitable for making various motor starting cabinets, including full-voltage direct-on-line starting cabinets, all-digital control soft starter cabinets, autotransformer reduced-voltage starting cabinets, star-delta starting cabinets, multi-speed motor starting cabinets, etc. Dozens of primary circuit scheme numbers or derived scheme numbers are available for selection, giving a wide range of applications. This product is an indoor enclosed distribution box. The enclosure is bent and welded from thin steel plate; the front has a single left-opening door fitted with measuring instruments such as a voltmeter and ammeter, and with operating and signal devices. It is a power distribution device with a simple structure, reliable operation and relatively low cost. The XL series products comply with the following standards: IEC 61439 Low-voltage switchgear and controlgear assemblies; GB/T 7251.12 Low-voltage switchgear and controlgear assemblies Part 2: Assemblies for power distribution and control.
Operating Environment
1. The ambient air temperature shall not exceed +40 °C and shall not be lower than -5 °C. The average temperature within 24 h shall not exceed +35 °C. 2. For indoor installation and use, the altitude of the installation site shall not exceed 2000 m. 3. The relative humidity of the ambient air shall not exceed 50% at a maximum temperature of +40 °C; higher relative humidity is permitted at lower temperatures, for example 90% at +20 °C, but occasional condensation may occur due to temperature changes. 4. During installation, the inclination from the vertical shall not exceed 5°. 5. The equipment shall be installed in locations free from severe vibration and shock, and where electrical components are not readily subject to corrosion. Note: If users have special requirements, these can be resolved through consultation with the manufacturer.
Technical Parameters
Rated operational voltage (Ue): V 380; Rated operational current (In): A ≤600; Rated frequency (Fn): Hz 50; Rated insulation voltage (Ui): V 660; Rated short-time withstand current (Icw): kA 10; Rated peak withstand current (Icw): kA 17; Rated impulse withstand voltage (Uimp): kV 6; Overvoltage category: IV; Pollution degree: 3; Clearance: ≥10 mm; Creepage distance: ≥12.5 mm; Degree of protection: IP30 (customizable on special request)
Dimensions
Height (mm) 1200~2000; Width (mm) 600~1000; Depth (mm) 350~600
Product Features
The XL low-voltage power distribution cabinet consists of the enclosure, molded-case circuit breakers, copper busbars, N busbar, PE busbar, PVC-insulated conductors, insulators, etc. The enclosure is made of cold-rolled steel plate by integral bending with partial welding, and its rigidity and load-bearing capacity meet the installation requirements of the electrical components. The front is a door; the rear is either an opening door or a closed back. The main circuit is connected with copper busbars; the surfaces of the copper busbars, N busbar and PE busbar are tin-plated. 1. Wiring method for insulated conductors of auxiliary circuits: insulated conductors are bundled with a spiral wrapping tube. 2. Installation method: floor-standing fixed installation. 3. Anti-corrosion measures: the enclosure surface is finished by electrostatic epoxy powder coating, and internal mounting parts are galvanized. 4. The degree of protection of the enclosure is generally IP30; users may also select between IP30 and IP42 according to the requirements of the operating environment.
